Buy TP-LINK TL-WA801ND Wireless N Access Point Up to 300Mbps/ Detachable Antenna x2/ Support AP, Client, Repeater, Bridge/ Up to 4 SSID with fast shipping and top-rated customer service. Once you know, you Newegg!
This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram. DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version (18.06 or later) onto it!
See for details.1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See what you can do now.2) OpenWrt support for this device will end after 2019.19.07 will be the last official build for 4/32 devices.
After 19.07, no further OpenWrt images will be built for 4/32 devices. See what you can do now. Since v3 hardware, TP-Link has started shipping with the new locked TP-link firmware. Investigation into this locking mechanism is still in progress, but the device does support tftp flashing. To use this feature, press and hold the reset button while powering on. The device will use the ip address 192.168.0.86, and attempt to load a new firmware from a tftp server at 192.168.0.66.
The v3 is looking for the file: wa801ndv3tprecovery.bin. Rename your openwrt-ar71xx-generic-tl-wa801nd-v3-squashfs-factory.bin file to wa801ndv3tprecovery.bin, confirmed working as of trunk r49037.However, this does not work with v4. Use the Workaround below instead.Firmware Workaround. A workaround for the locked firmware has been found, based on Keyboardgnome's solution for the WR710n. The key is that a command can be injected by including it as part of the SSID.
Several SSIDs are set which compile a script in the router's ram, and then a final command executes that script. After about 60 seconds, the web interface will be available again, and should accept an Openwrt image.To use the workaround, set the device's SSID to each of the following lines, making sure to include the backticks. Set the ssid and click save between each line.`echo 'httpd -k' /tmp/s``echo 'sleep 10' /tmp/s``echo 'httpd -r&' /tmp/s``echo 'sleep 10' /tmp/s``echo 'httpd -k' /tmp/s``echo 'sleep 10' /tmp/s``echo 'httpd -f' /tmp/s``sh /tmp/s` Unsorted. Out of the box even if the serial header is present and has the typical TP-Link pinout, it won’t work, because some resistors are missing from the board, namely R105 and R107.TL-WA801ND v3 solder bridge requiredSolder bridge on R105 required to receive data from the serial portTL-WA801ND v3 solder bridge requiredSolder bridge on R107 to allow sending to serial portThe serial port settings are, as usual 115200 baud and to enter uboot prompt you have to quickly type “tpl” when it says that it is waiting 1 second.Installing from the web interface.
COPYRIGHT & TRADEMARKSSpecifications are subject to change without notice. Is a registered trademark of TP-LINKTECHNOLOGIES CO., LTD.
Other brands and product names are trademarks or registered trademarks of their respective holders.No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINKTECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINKTECHNOLOGIES CO., LTD.All rights reserved.http://www.tp-link.com. FCC STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.FCC RF Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-locatedor operating in conjunction with any other antenna or transmitter.“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-locatedor operating in conjunction with any other antenna or transmitter.”CE Mark WarningThis is a class B product.
![Setting tp link tl wa801nd setup Setting tp link tl wa801nd setup](/uploads/1/2/5/5/125512052/687408776.jpg)
In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. 4.8.5Factory Defaults.594.8.6Backup & Restore.594.8.7Reboot.604.8.8Password.604.8.9System Log.61Appendix A: Application Example.62Appendix B: Factory Defaults.65Appendix C: Troubleshooting.66Appendix D: Specifications.71Appendix E: Glossary.72. TL-WA801ND 300Mbps Wireless N Access Point User Guide Package Contents¾ The following items should be found in your package:¾ One TL-WA801ND300Mbps Wireless N Access Point¾ One Power Injector¾ Ethernet Cable¾ One Power Adapter for TL-WA801ND300Mbps Wireless N Access Point¾ Quick Installation Guide¾ One Resource CD for TL-WA801ND300Mbps Wireless N Access Point, including: z This User Guidez Other helpful information) Note:Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. TL-WA801ND 300Mbps Wireless N Access Point User Guide Chapter 1 Introduction 1.1 Product OverviewThe TL-WA801ND300Mbps Wireless N Access Point is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It allows for greater range and mobility within your wireless network while also allowing you to connect the wireless devices to a wired environment. Increased mobility and the absence of cabling will be beneficial for your network.With using IEEE 802.11n wireless technology, your device can transmit wireless data at the rate of up to 300Mbps.
![Tp link tl-wa801nd lights Tp link tl-wa801nd lights](/uploads/1/2/5/5/125512052/662211342.jpg)
With multiple protection measures, including SSID broadcast control and wireless LAN 64/128/152-bitWEP encryption, WiFi protected Access (WPA2PSK, WPAPSK), the TL-WA801ND300Mbps Wireless N Access Point delivers complete data privacy. This device leverages some 802.11n features to provide improved performance and coverage compared to 802.11a/g devices, and fully interoperates with 802.11n products if they are Wi-FiCERTIFIED, but it does not conform to all of the requirements in the IEEE specification and is not classified as 'n' in the Wi-FiCERTIFIED program.It supports an easy, web-basedsetup for installation and management. Even though you may not be familiar with the Access Point, you can easily configure it with the help of this Guide. Before installing the AP, please look through this Guide to get the full information of the TL-WA801ND300Mbps Wireless N Access Point. 1.2 ConventionsThe AP or TL-WA801ND,or device mentioned in this User guide stands for TL-WA801ND300Mbps Wireless N Access Point without any explanations.Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.
You can set the parameters according to your demand.